Introduction
Why Farm Worms?
Farming at Home
Money from Worms?
About the Worms
Traditional Worm Farming
Make Your own Farm
The Right Environment
Vermiculture Pests
Dictionary: Worm Terms
Reproduction
Worm Tea

How to Make Your Own Worm Farm

Why buy an expensive worm farm, when you can set up a perfectly good stacking system wormery, for less than  half the price of buying in a fancy branded worm farm from a dealer? You won’t even need to be much of a handyman, nor use expensive materials to produce a neat unit that will look good and function well.

                                                                                                                              Worm Dictionary

Page Index

The Principle of the Stacked Bin Worm Farm

Choosing Your Bins

Instructions for Creating Your DIY Worm Composter

The Sump

The Composting Bins

Setting it Up

Starting Production

- Worm Terms Dictionary 

 

 

The Principle of the Stacked Bin Worm Farm

 

Traditional methods of vermiculture have their place, but today’s suburban worm farmer wants a composting system that takes up minimal space, looks good and is clean and convenient to use.  The home worm farmer, or amateur vermiculturalist can use suitable modern products and a better understanding of the habits and requirements of the compost worms in the worm bins to design a system that is both convenient to handle and efficient in the usage of materials and manpower.

 

Inexpensive 3 bin composting worm farm

An inexpensive DIY worm farm

The principle of the stacked bin worm composter is that, unlike the drab earthworms, who dig deep, our red compost worms always migrate upwards, towards the food, leaving their castings to fall below them. We use this information about red worms to our advantage. Generally the idea is to build up a multiple stacking system of connected worm bins or trays that are slightly tapered to allow the bins to nest, one within the other. Worm castings (the compost) are collected in the lower bins and worm food (kitchen or garden scraps) is consumed in the upper levels of the wormery. When a lower bin is nearly full of castings it is emptied and rotated to the top and so on.

 

 Back to Top

 

Choosing Your Bins

 

The size and number of the nesting bins is variable, depending on the desired scale of the operation. Common plastic storage bins, sold for general household use at hardware stores, supermarkets and camping goods outlets are quite suitable for making your worm farm.  Usually the sides are not vertical, but slightly tapered for convenient stacking on the retailer’s shelves – this suits us, as it allows for partial nesting of bins . A lid would be required for the top bin. Worms hate light – so don’t get opaque bins. Heavy black bins are good. The plastic storage containers are not expensive and come in a variety of sizes. For a small scale composting set-up, for processing  kitchen waste, three containers of about 45 litre (ten gallon) each would be adequate. For processing a greater amount of waste such as from large gardens or stables, bigger bins with more tiers can be set up, just as easily.

 Back to Top

 

Instructions for Creating Your DIY Worm Composter

 

cross sectiona diagram of a 3 bin composter

Cross sectional diagram of Three Bin Composter.

 Back to Top

 

 


The Sump

 

The lower sump bin is configured differently from the upper bins and would be prepared first. Its function is to collect excess fluid leachate, called worm tea, or compost tea.

  • The sump may be fitted with a 3/8 inch (15mm) barrel tap, through a small hole drilled in the base for conveniently draining out the excess fluid (the worm tea) that will accumulate there. This tap is not essential, but would avoid the otherwise potentially messy job of having to tip the worm tea out by rotating the bin.
  • If you do decide to put in the tap, make sure it seals well in the hole, by providing good washers and lock nuts.

 

tapping off the worm tea

Tapping off the worm tea.

 Back to Top

 


The Composting Bins


The two upper bins will actually hold the worms. They are to be identical and are prepared as follows : -

  • Drill a pattern of ¼ inch (6mm) holes across the entire base of each  container for drainage and to allow for ventilation and the upward migration of the compost worms, these holes should be regularly spaced  at approx two inches (50mm) centres apart in either direction.
  • For further aeration, drill a row of ¼ inch (6mm) holes at two inch (50mm) centres, in a continuous line around the walls of each of the bins. This line of holes would be about four inches (100mm) below the top rim of the bin.
  • It is not essential to drill holes in the lid, which is closed tightly over the upper bin. as you should get enough air through the sides.

     Back to Top



Setting It Up


After preparing your bins, you first set up the lower (sump) bin on bricks or blocks, allowing enough space to tap off the fluid from beneath it. Choose a shady location for the worm farm (in a shed or garage, if you are subject to frosts).

  • The second and third bins are “nested” within each other and dropped into the sump bin. To maintain a working space for the worms, and for accumulation of compost, you need a few spacers or  packers of about six to eight inches height, between the two upper bins and some smaller packers of about four inches in the lower (sump) bin. You can use wood blocks or sealed food jars for packers.
  • The packers also prevent the tapered worm bins from jamming together and cause a gap between the bins, which improves ventilation.
  • To prevent “nasty bugs” from squeezing in between the bins, you should close (caulk)  the small gap between them with strips of shade cloth, or mosquito netting. .

     Back to Top


 

Starting Production


Now you are ready to go into production : -

  • Set up your worms in the top bin with a good (damp) fibrous bedding such as coconut coir, (or just shredded newspaper), put in a little compost and a handful or two of damp soil with the worms and after a few days you will be ready to start feeding in your kitchen scraps. Cover the food with more bedding material to discourage pests and keep the lid closed.
  • Make sure the worm farm is never allowed to dry out, by sprinkling water over the bedding periodically, if there is not already enough moisture coming from the food scraps.
  • When the top bin has been fully productive for a while, the worms will multiply and compost will be start accumulating from the worm castings. When the quantity of compost is meaningful, stop putting feed into this bin and swap over the upper two bins by putting bin No 2 to the top of the stack, with bin No 1 now in the middle.
  • Set up this new top bin with clean bedding, a small amount of the old castings and immediately start feeding your  kitchen scraps into it. Over a few days, the worms will naturally migrate upwards towards the new food source, leaving the lower bin with only a few stragglers and it should be ready for the harvesting of your compost within about three weeks after the swap.
  • To get at any specific layer, to add food, bedding or to remove the vermicompost, just lift off all the overlying worm bins, one by one until the desired level is exposed for examination and then replace them in the same order. They will not be too heavy – but don’t try lifting more than one layer at a time, unless you have a good chiropractor!

All you need to do is to keep repeating the process of alternating the top two bins on a regular basis, taking out the compost, whenever it accumulates, and tapping off the worm tea from time to time. This vermitea, is a very valuable product as it is a highly concentrated liquid fertilizer that can be diluted for immediate use on your garden.

 

Further useful information can be seen about making a low budget worm farm at an ezine article, written by us: making a low budget worm farm.

 Back to Top

 

Next Page >